Every monitor has a maximum refresh rate it is capable of displaying at a given resolution (for example, a typical 17-inch monitor of a few years ago will happily crank out 85Hz or more at a resolution of 800x600, but may only be capable of 60Hz at 1600x1200).
If this refresh rate is exceeded, the image will be distorted and unusable.
Older CRT monitors, especially 15-inch or smaller ones, tend not to be capable of a refresh rate much over 60Hz, especially at resolutions greater than 640X480. Also, setting the refresh rate does not have the same effect on LCD or flat panel monitors, as their screens are not redrawn in the same way.
To change your monitor refresh rate: Right click on an empty space on your desktop (no icons) and select 'properties.' Click the 'settings' tab and choose the 'advanced' button. Now choose the 'adaptor' tab and click the 'show all modes' button.
This presents you with a list of resolution, colour and refresh rate options that your video card\monitor combination is capable of displaying. You can experiment with these settings by using the 'apply' button. Note that a refresh rate of 75Hz or above is generally recommended, (keep in mind most monitors do not support settings higher than 85Hz).
After you set the refresh rate, you may feel a little uncomfortable for a short while as your eyes adjust, but rest assured you will grow to appreciate the difference in ease of viewing.
Showing posts with label Hard Disk OR Drivers. Show all posts
Showing posts with label Hard Disk OR Drivers. Show all posts
Tuesday, 2 October 2007
Convert a FAT partition to NTFS
Click Start, click Programs, and then click Command Prompt.
In Windows XP, click Start, click Run, type cmd and then click OK.
At the command prompt, type CONVERT [driveletter]: /FS:NTFS.
Convert.exe will attempt to convert the partition to NTFS.
NOTE: Although the chance of corruption or data loss during the conversion from FAT to NTFS is minimal, it is best to perform a full backup of the data on the drive that it is to be converted prior to executing the convert command. It is also recommended to verify the integrity of the backup before proceeding, as well as to run RDISK and update the emergency repair disk (ERD).
In Windows XP, click Start, click Run, type cmd and then click OK.
At the command prompt, type CONVERT [driveletter]: /FS:NTFS.
Convert.exe will attempt to convert the partition to NTFS.
NOTE: Although the chance of corruption or data loss during the conversion from FAT to NTFS is minimal, it is best to perform a full backup of the data on the drive that it is to be converted prior to executing the convert command. It is also recommended to verify the integrity of the backup before proceeding, as well as to run RDISK and update the emergency repair disk (ERD).
Using advanced file security settings in विन्डोज़ NTFS
Using advanced file security settings in Windows
Windows XP is based on the same platform as Windows 2000, and shares that operating system's robust file security options, at least when using the NTFS file system. Unfortunately this security system, which enables an administrator to decide exactly which files and programs any given user will have access to, is not actually implemented by default in Windows XP. This is a concession Microsoft made to avoid confusing basic users of XP Pro, and to cripple XP Home.
The NTFS file security options can be enabled easily enough in XP Pro, but are apparently non-existent in the Home version. Fact is, the tools are there, you just need to look a little bit harder.
To enable NTFS file security in Windows XP Home: First you need to assure that at least your main hard drive is formatted with the NTFS file system. See tip #61 for instructions on this. Restart your system. Just after the memory and BIOS check screen, but before the Windows splash screen comes up, press F8 a few times.
When the Windows boot menu appears, select 'safe mode' from the list of options.
Once Windows has loaded in safe mode, right click the folders and files you would like to change access to. You will notice that the 'security' tab now exists, and thus you are allowed to assign or deny access to individual users for each file, folder and program. Once you are done, restart Windows normally, and your changes will be enforced.
Windows XP is based on the same platform as Windows 2000, and shares that operating system's robust file security options, at least when using the NTFS file system. Unfortunately this security system, which enables an administrator to decide exactly which files and programs any given user will have access to, is not actually implemented by default in Windows XP. This is a concession Microsoft made to avoid confusing basic users of XP Pro, and to cripple XP Home.
The NTFS file security options can be enabled easily enough in XP Pro, but are apparently non-existent in the Home version. Fact is, the tools are there, you just need to look a little bit harder.
To enable NTFS file security in Windows XP Home: First you need to assure that at least your main hard drive is formatted with the NTFS file system. See tip #61 for instructions on this. Restart your system. Just after the memory and BIOS check screen, but before the Windows splash screen comes up, press F8 a few times.
When the Windows boot menu appears, select 'safe mode' from the list of options.
Once Windows has loaded in safe mode, right click the folders and files you would like to change access to. You will notice that the 'security' tab now exists, and thus you are allowed to assign or deny access to individual users for each file, folder and program. Once you are done, restart Windows normally, and your changes will be enforced.
Monday, 1 October 2007
Set monitor refresh rate
Every monitor has a maximum refresh rate it is capable of displaying at a given resolution (for example, a typical 17-inch monitor of a few years ago will happily crank out 85Hz or more at a resolution of 800x600, but may only be capable of 60Hz at 1600x1200).
If this refresh rate is exceeded, the image will be distorted and unusable.
Older CRT monitors, especially 15-inch or smaller ones, tend not to be capable of a refresh rate much over 60Hz, especially at resolutions greater than 640X480. Also, setting the refresh rate does not have the same effect on LCD or flat panel monitors, as their screens are not redrawn in the same way.
To change your monitor refresh rate: Right click on an empty space on your desktop (no icons) and select 'properties.' Click the 'settings' tab and choose the 'advanced' button. Now choose the 'adaptor' tab and click the 'show all modes' button.
This presents you with a list of resolution, colour and refresh rate options that your video card\monitor combination is capable of displaying. You can experiment with these settings by using the 'apply' button. Note that a refresh rate of 75Hz or above is generally recommended, (keep in mind most monitors do not support settings higher than 85Hz).
After you set the refresh rate, you may feel a little uncomfortable for a short while as your eyes adjust, but rest assured you will grow to appreciate the difference in ease of viewing.
If this refresh rate is exceeded, the image will be distorted and unusable.
Older CRT monitors, especially 15-inch or smaller ones, tend not to be capable of a refresh rate much over 60Hz, especially at resolutions greater than 640X480. Also, setting the refresh rate does not have the same effect on LCD or flat panel monitors, as their screens are not redrawn in the same way.
To change your monitor refresh rate: Right click on an empty space on your desktop (no icons) and select 'properties.' Click the 'settings' tab and choose the 'advanced' button. Now choose the 'adaptor' tab and click the 'show all modes' button.
This presents you with a list of resolution, colour and refresh rate options that your video card\monitor combination is capable of displaying. You can experiment with these settings by using the 'apply' button. Note that a refresh rate of 75Hz or above is generally recommended, (keep in mind most monitors do not support settings higher than 85Hz).
After you set the refresh rate, you may feel a little uncomfortable for a short while as your eyes adjust, but rest assured you will grow to appreciate the difference in ease of viewing.
Convert a FAT partition to NTFS
Click Start, click Programs, and then click Command Prompt.
In Windows XP, click Start, click Run, type cmd and then click OK.
At the command prompt, type CONVERT [driveletter]: /FS:NTFS.
Convert.exe will attempt to convert the partition to NTFS.
NOTE: Although the chance of corruption or data loss during the conversion from FAT to NTFS is minimal, it is best to perform a full backup of the data on the drive that it is to be converted prior to executing the convert command. It is also recommended to verify the integrity of the backup before proceeding, as well as to run RDISK and update the emergency repair disk (ERD).
In Windows XP, click Start, click Run, type cmd and then click OK.
At the command prompt, type CONVERT [driveletter]: /FS:NTFS.
Convert.exe will attempt to convert the partition to NTFS.
NOTE: Although the chance of corruption or data loss during the conversion from FAT to NTFS is minimal, it is best to perform a full backup of the data on the drive that it is to be converted prior to executing the convert command. It is also recommended to verify the integrity of the backup before proceeding, as well as to run RDISK and update the emergency repair disk (ERD).
Using advanced file security settings in विन्डोज़ NTFS
Using advanced file security settings in Windows
Windows XP is based on the same platform as Windows 2000, and shares that operating system's robust file security options, at least when using the NTFS file system. Unfortunately this security system, which enables an administrator to decide exactly which files and programs any given user will have access to, is not actually implemented by default in Windows XP. This is a concession Microsoft made to avoid confusing basic users of XP Pro, and to cripple XP Home.
The NTFS file security options can be enabled easily enough in XP Pro, but are apparently non-existent in the Home version. Fact is, the tools are there, you just need to look a little bit harder.
To enable NTFS file security in Windows XP Home: First you need to assure that at least your main hard drive is formatted with the NTFS file system. See tip #61 for instructions on this. Restart your system. Just after the memory and BIOS check screen, but before the Windows splash screen comes up, press F8 a few times.
When the Windows boot menu appears, select 'safe mode' from the list of options.
Once Windows has loaded in safe mode, right click the folders and files you would like to change access to. You will notice that the 'security' tab now exists, and thus you are allowed to assign or deny access to individual users for each file, folder and program. Once you are done, restart Windows normally, and your changes will be enforced.
Windows XP is based on the same platform as Windows 2000, and shares that operating system's robust file security options, at least when using the NTFS file system. Unfortunately this security system, which enables an administrator to decide exactly which files and programs any given user will have access to, is not actually implemented by default in Windows XP. This is a concession Microsoft made to avoid confusing basic users of XP Pro, and to cripple XP Home.
The NTFS file security options can be enabled easily enough in XP Pro, but are apparently non-existent in the Home version. Fact is, the tools are there, you just need to look a little bit harder.
To enable NTFS file security in Windows XP Home: First you need to assure that at least your main hard drive is formatted with the NTFS file system. See tip #61 for instructions on this. Restart your system. Just after the memory and BIOS check screen, but before the Windows splash screen comes up, press F8 a few times.
When the Windows boot menu appears, select 'safe mode' from the list of options.
Once Windows has loaded in safe mode, right click the folders and files you would like to change access to. You will notice that the 'security' tab now exists, and thus you are allowed to assign or deny access to individual users for each file, folder and program. Once you are done, restart Windows normally, and your changes will be enforced.
Thursday, 27 September 2007
To change Drive Letters
To change Drive Letters:
Go to Start > Control Panel > Administrative Tools > Computer Management, Disk Management, then right-click the partition whose name you want to change (click in the white area just below the word "Volume") and select "change drive letter and paths." From here you can add, remove or change drive letters and paths to the partition
Go to Start > Control Panel > Administrative Tools > Computer Management, Disk Management, then right-click the partition whose name you want to change (click in the white area just below the word "Volume") and select "change drive letter and paths." From here you can add, remove or change drive letters and paths to the partition
To change Drive Letters
To change Drive Letters:
Go to Start > Control Panel > Administrative Tools > Computer Management, Disk Management, then right-click the partition whose name you want to change (click in the white area just below the word "Volume") and select "change drive letter and paths." From here you can add, remove or change drive letters and paths to the partition
Go to Start > Control Panel > Administrative Tools > Computer Management, Disk Management, then right-click the partition whose name you want to change (click in the white area just below the word "Volume") and select "change drive letter and paths." From here you can add, remove or change drive letters and paths to the partition
Subscribe to:
Posts (Atom)